Disable-SbecBcd

Disable-SbecBcd is accessible with the help of BootEventCollector module. To configure BootEventCollector, go through this link.

Synopsis

Disables the event forwarding mode in BCD settings.

Description

The Disable-SbecBcd cmdlet disables the Boot Configuration Data (BCD) /event flag. This operation has no effect on the current connections; you must reboot the computer for the settings to take effect.

You can apply these changes to the local computer, to a remote computer, or to an offline disk image.

To operate on a local computer, specify the Local parameter. Enabling forwarding on the computer that runs the Collector service makes sense only if it sends the data to a Collector on a different computer. Otherwise, the in-kernel module is not able to connect to the Collector. However, you can copy the PowerShell BootEventCollector module to the other computers, where you can use it for local configuration.

To operate on a remote computer, specify either the ComputerName or Session parameter. Windows PowerShell remoting is used to perform the remote operations.

To operate on an offline (WIM or VHD) image, use the Path parameter. WIM images do not normally contain the BCD files, and there is rarely a need to replace them there. Instead, Windows Setup creates the BCD settings when it extracts the image from WIM to the hard drive.

Parameters

-BcdStore

Specifies the full path of the BCD store.

-ComputerName

Specifies the names of the computers on which you want to perform the operation. You can specify a fully qualified domain name (FQDN), a NetBIOS name, or an IP address for each computer. For more information, see Invoke-CimMethod on TechNet.

-Credential

Specifies a user account that has permission to perform this action. The default is the current user.

-DismLogPath

Specifies the path of the file for the Deployment Image Servicing and Management (DISM) log when mounting images.

-Id

Specifies the ID of the entry to disable, without the curly braces.

The BCD settings may contain entries for multiple boot images (when a computer has multiple operating system versions installed). When the settings for an operating system other than the currently running one (or the default operating system in an offline image) must be modified, you can use this parameter to select the entry.

-Local

Indicates that this operation occurs on the local computer. This mode also allows the extra control over the BCD store of where the settings are applied.

-Path

Specifies the list of full paths to the offline Windows image files (WIM or VHD) to which to apply the settings. If a WIM file contains multiple images, all of them are modified.

-Session

Specifies the PSSession objects connected to the remote target computers. Enter a session object, such as the output of the Get-PSSession or New-PSSession cmdlet, or an array of these objects.

Syntax

Disable-SbecBcd -Path <String[]> [-Id <String>] [-DismLogPath <String>] [<CommonParameters>]

Disable-SbecBcd -ComputerName <String[]> [-Credential <PSCredential>] [-Id <String>] [<CommonParameters>]

Disable-SbecBcd -Session <PSSession[]> [-Id <String>] [<CommonParameters>]

Disable-SbecBcd [-Local] [-BcdStore <String>] [-Id <String>] [<CommonParameters>]

—————–Example 1—————–
Disable BCD
PS C:\> Disable-SbecBcd -Session $MyPSSession
This command disables the BCD settings on a remote session.

You can check the Version, CommandType and Source of this cmdlet by giving below command.

Get-Command Disable-SbecBcd

You can also read about

To know more PowerShell cmdlets(Commands) on BootEventCollector click here

Click on this Link for an Single place where you get all the PowerShell cmdlet sorted based on the modules.

You can also refer other blogs on PowerShell at link

You can also refer other blogs on Microsoft at link

And also if you required any technology you want to learn, let us know below we will publish them in our site http://tossolution.com/

Like our page in Facebook and follow us for New technical information.

References are taken from Microsoft