Set-DhcpServerv6Scope

Set-DhcpServerv6Scope is accessible with the help of DHCPServer module. To configure DHCPServer, go through this link.

Synopsis

Modifies the properties of the IPv6 scope on the Dynamic Host Configuration Protocol (DHCP) server service.

Description

The Set-DhcpServerv6Scope cmdlet modifies the properties of the IPv6 scope on the Dynamic Host Configuration Protocol (DHCP) server service.

Parameters

-AsJob

Runs the cmdlet as a background job. Use this parameter to run commands that take a long time to complete. The cmdlet immediately returns an object that represents the job and then displays the command prompt. You can continue to work in the session while the job completes. To manage the job, use the *-Job cmdlets. To get the job results, use the Receive-Job cmdlet. For more information about Windows PowerShell background jobs, see about_Jobs.

-CimSession

Runs the cmdlet in a remote session or on a remote computer. Enter a computer name or a session object, such as the output of a New-CimSession or Get-CimSession cmdlet. The default is the current session on the local computer.

-ComputerName

Specifies the DNS name, or IPv4 or IPv6 address, of the target computer that runs the DHCP server service.

-Confirm

Prompts you for confirmation before running the cmdlet.

-Description

Specifies the description to set on the scope.

-Name

Specifies the new name to set for the scope.

-PassThru

Returns an object representing the item with which you are working. By default, this cmdlet does not generate any output.

-Preference

Specifies the preference value of the DHCP server service. The DHCP server service that has the lowest preference value is selected by the DHCP client in case the client gets responses from more than one DHCP server service.

-PreferredLifeTime

Specifies the preferred life time of the IPv6 address leased by the DHCP server service. This parameter value should be same or less than the ValidLifeTime parameter value.

-Prefix

Specifies the IPv6 subnet prefix of the scope for which the properties are modified.

-State

Specifies the state of the scope. The acceptable values for this parameter are: Active or Inactive.

-T1

Specifies the lease renewal time. The DHCP client is expected to use a unicast message to renew the lease at the time specifies by this parameter value from the same DHCP server service from which DHCP client had at first obtained the lease. This parameter value should be less than the T2 and PreferredLifetime parameter values for the scope.

-T2

Specifies the lease rebind time. The client is expected to use a multi-cast message to renew the lease at the time equal to this parameter value from any DHCP server service if the renewal attempt at time specified by the T1 parameter fails. This parameter value should be larger than the T1 parameter value and less than the PreferredLifetime parameter value.

-ThrottleLimit

Specifies the maximum number of concurrent operations that can be established to run the cmdlet. If this parameter is omitted or a value of 0 is entered, then Windows PowerShell calculates an optimum throttle limit for the cmdlet based on the number of CIM cmdlets that are running on the computer. The throttle limit applies only to the current cmdlet, not to the session or to the computer.

-ValidLifeTime

Specifies the valid life time of the IPv6 address leased by the DHCP server service. This parameter value should be same or larger than the PreferredLifetime parameter value.

-WhatIf

Shows what would happen if the cmdlet runs. The cmdlet is not run.

Syntax

Set-DhcpServerv6Scope [-Prefix] <IPAddress> [-Name <String>] [-Description <String>] [-State <String>] [-Preference <UInt16>] [-PreferredLifeTime <TimeSpan>] [-ValidLifeTime <TimeSpan>] [-T1 <TimeSpan>] [-T2 <TimeSpan>] [-ComputerName <String>] [-PassThru] [-CimSession <CimSession[]>] [-ThrottleLimit <Int32>] [-AsJob] [-WhatIf] [-Confirm] [<CommonParameters>]

—————EXAMPLE 1—————
PS C:>Set-DhcpServerv6Scope -ComputerName dhcpsrv.TOSSolution.com -Prefix 2001:4898:7020:1111:: -Name “SF VLAN100” -State Active
This example changes the name of the specified DHCPv6 scope to SF VLAN100 and activates the scope.

You can check the Version, CommandType and Source of this cmdlet by giving below command.

Get-Command Set-DhcpServerv6Scope

You can also read about

To know more PowerShell cmdlets(Commands) on DHCPServer click here

Click on this Link for an Single place where you get all the PowerShell cmdlet sorted based on the modules.

You can also refer other blogs on PowerShell at link

You can also refer other blogs on Microsoft at link

And also if you required any technology you want to learn, let us know below we will publish them in our site http://tossolution.com/

Like our page in Facebook and follow us for New technical information.

References are taken from Microsoft