Add-DhcpServerv6ExclusionRange

Add-DhcpServerv6ExclusionRange is accessible with the help of DHCPServer module. To configure DHCPServer, go through this link.

Synopsis

Sets the range of IPv6 addresses to exclude from an IPv6 scope.

Description

The Add-DhcpServerv6ExclusionRange cmdlet sets the range of IPv6 addresses to exclude from an IPv6 scope. The IP addresses from this range will not be leased out by the Dynamic Host Configuration Protocol (DHCP) server service.

Parameters

-AsJob

Runs the cmdlet as a background job. Use this parameter to run commands that take a long time to complete. The cmdlet immediately returns an object that represents the job and then displays the command prompt. You can continue to work in the session while the job completes. To manage the job, use the *-Job cmdlets. To get the job results, use the Receive-Job cmdlet. For more information about Windows PowerShell background jobs, see about_Jobs.

-CimSession

Runs the cmdlet in a remote session or on a remote computer. Enter a computer name or a session object, such as the output of a New-CimSession or Get-CimSession cmdlet. The default is the current session on the local computer.

-ComputerName

Specifies the DNS name, or IPv4 or IPv6 address, of the target computer that runs the DHCP server service.

-Confirm

Prompts you for confirmation before running the cmdlet.

-EndRange

Specifies the ending IP address in exclusion range, as a string formatted as an IPv6 address.

-PassThru

Returns an object representing the item with which you are working. By default, this cmdlet does not generate any output.

-Prefix

Specifies the IPv6 prefix of the scope to which the exclusion range is added.

-StartRange

Specifies the starting IP address in exclusion range, as a string formatted as an IPv6 address.

-ThrottleLimit

Specifies the maximum number of concurrent operations that can be established to run the cmdlet. If this parameter is omitted or a value of 0 is entered, then Windows PowerShell calculates an optimum throttle limit for the cmdlet based on the number of CIM cmdlets that are running on the computer. The throttle limit applies only to the current cmdlet, not to the session or to the computer.

-WhatIf

Shows what would happen if the cmdlet runs. The cmdlet is not run.

Syntax

Add-DhcpServerv6ExclusionRange [-ComputerName <String>] [-StartRange] <IPAddress> [-EndRange] <IPAddress> [-Prefix] <IPAddress> [-PassThru] [-CimSession <CimSession[]>] [-ThrottleLimit <Int32>] [-AsJob] [-WhatIf] [-Confirm] [<CommonParameters>]

——————EXAMPLE 1——————
PS C:>Add-DhcpServerv6ExclusionRange -Prefix 2406:7400:73:932f:: -StartRange 2406:7400:73:932f::1 -EndRange 2406:7400:73:932f::10
This example excludes the IPv6 addresses from 2406:7400:73:932f::1 to 2406:7400:73:932f::10 from DHCPv6 scope 2406:7400:73:932f:: on the DHCP server service running on the local computer.

——————EXAMPLE 2——————
PS C:>Add-DhcpServerv6ExclusionRange -ComputerName dhcpsrv.TOSSolution.com -Prefix 2406:7400:73:932f:: -StartRange 2406:7400:73:932f::1 -EndRange 2406:7400:73:932f::1
This example excludes the IPv6 address 2406:7400:73:932f::1 from the DHCPv6 scope 2406:7400:73:932f:: on the DHCP server service running on the computer named dhcpsrv.TOSSolution.com.

You can check the Version, CommandType and Source of this cmdlet by giving below command.

Get-Command Add-DhcpServerv6ExclusionRange

You can also read about

To know more PowerShell cmdlets(Commands) on DHCPServer click here

Click on this Link for an Single place where you get all the PowerShell cmdlet sorted based on the modules.

You can also refer other blogs on PowerShell at link

You can also refer other blogs on Microsoft at link

And also if you required any technology you want to learn, let us know below we will publish them in our site http://tossolution.com/

Like our page in Facebook and follow us for New technical information.

References are taken from Microsoft