Checkpoint-SbecActiveConfig

Checkpoint-SbecActiveConfig is accessible with the help of BootEventCollector module. To configure BootEventCollector, go through this link.

Synopsis

Creates a configuration checkpoint.

Description

The Checkpoint-SbecActiveConfig cmdlet creates a checkpoint for the active Boot Event Collector configuration.

The checkpoint enables you to return to this configuration later using the Undo-SbecActiveConfig, Redo-SbecActiveConfig, and Restore-SbecBackupConfig cmdlets. The checkpoints mark the known good configurations that you can revert to if a new configuration is incorrect. For example, if you changed a configuration yesterday, find an issue with it today, and want to revert to yesterday’s configuration before you made a change, you can use the checkpointed configuration from yesterday.

Most checkpoints are created automatically, but on rare occasions you might need to explicitly create them. Automatic checkpoints are created when the current configuration has not yet been checkpointed and one of the following events occurs:

A checkpoint ensures that the current configuration is remembered, but it doesn’t immediately create a backup configuration file. Instead, the checkpointed current configuration is saved to a backup file when the configuration changes.

The repeated checkpointing succeeds but has no effect, because it only flags the configuration to create a backup in the future.

The Undo-SbecActiveConfig, Redo-SbecActiveConfig, and Restore-SbecBackupConfig cmdlets change the current configuration by browsing through the backup configurations, but they don’t do an immediate checkpointing. This lets you browse through the past configurations, try them out, and change your mind if a configuration doesn’t work well without causing a flurry of spurious checkpoints and backup files with identical content. When you are satisfied with a configuration, checkpoint it with Checkpoint-SbecActiveConfig. If you forget to create a checkpoint for a configuration, it is automatically checkpointed after an hour.

Use Get-SbecBackupConfig to get the list of backup configuration files.

You can use the OldTimestamp parameter to modify the configuration atomically.

You must have the Builtin Administrator rights to run the cmdlet.

Parameters

-CimSession

Runs the cmdlet on the remote computers through a remote session. Enter a session object, such as the output of a New-CimSession or Get-CimSession cmdlet, or an array of these objects. The default is to run the cmdlet on the local computer. For more information, see About_CimSession.

-ComputerName

Specifies the names of the computers on which you want to perform the operation. You can specify a fully qualified domain name (FQDN), a NetBIOS name, or an IP address for each computer. For more information see Invoke-CimMethod on MSDN.

-Continue

Indicates that this operation will not throw an exception if a failure occurs. Instead, the caller should examine the output of the cmdlet for the error information.

-OldTimestamp

Specifies the timestamp of the previous active configuration. This provides a way to perform the atomic changes of the configuration.

Each configuration has a timestamp (the time when it was last set or restored) and an original timestamp (if the configuration was restored, the time when it was originally set, otherwise the same as the normal timestamp). This operation checks that the OldTimestamp value matches either the normal or original timestamp of the current active configuration, thus ensuring that the active configuration has not changed since the last time you examined it. If the values do not match, an error is returned.

Syntax

Checkpoint-SbecActiveConfig [[-OldTimestamp] <UInt64>] [-Continue] [[-ComputerName] <String[]>] [[-CimSession] <CimSession[]>] [<CommonParameters>]

—————–Example 1—————–
Undo a configuration and create a checkpoint
PS C:\> Undo-SbecActiveConfig | Format-List; Checkpoint-SbecActiveConfig | Format-List
This command undoes a configuration and creates a checkpoint, in a simple way. Format-List formats the information that this cmdlet returns.

—————–Example 2—————–
Undo a configuration and create a checkpoint atomically
PS C:\> $res = Undo-SbecActiveConfig | Format-List PS C:\> $res = Checkpoint-SbecActiveConfig -OldTimestamp $res.OriginalTimestamp | Format-LIst
This command undoes a configuration and creates a checkpoint, making sure that no other changes are done in between, and throwing on errors.

You can check the Version, CommandType and Source of this cmdlet by giving below command.

Get-Command Checkpoint-SbecActiveConfig

You can also read about

To know more PowerShell cmdlets(Commands) on BootEventCollector click here

Click on this Link for an Single place where you get all the PowerShell cmdlet sorted based on the modules.

You can also refer other blogs on PowerShell at link

You can also refer other blogs on Microsoft at link

And also if you required any technology you want to learn, let us know below we will publish them in our site http://tossolution.com/

Like our page in Facebook and follow us for New technical information.

References are taken from Microsoft